Karoseria i wnętrze, Nissan Primera P11 -- P11.144

[ Pobierz całość w formacie PDF ]
BODY & TRIM
SECTION
BT
CONTENTS
............................................................. 2
............................................................ 2
Supplemental Restraint System (SRS)
²
AIR
........................................................ 30
................................................................... 31
............................................................................ 40
................................................................ 40
............................................................. 42
................................................................ 43
.................................................................... 46
................................................... 49
.................................. 53
................................. 54
............................................................ 55
.................................................. 56
....................................................................... 58
............................................................... 58
....................................................... 59
..................................................... 60
............................................... 60
............................................................... 62
............. 2
................................................. 3
...................................................... 3
.................................................................... 5
......................................................... 5
...................................... 7
........................................................................... 13
............................................................... 13
................................................................ 14
................................................. 15
.......................................................... 18
................................................. 18
................................................................. 24
................................................................. 25
..................................................... 28
................................................ 29
²
and
²
SEAT BELT PRE-TENSIONER
²
BT
BAG
PRECAUTIONS
Service Notice
l
When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent
scratches.
l
Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to soil
or damage them.
l
Apply sealing compound where necessary when installing parts.
l
When applying sealing compound, be careful that the sealing compound does not protrude from parts.
l
When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust
prevention measures.
Supplemental Restraint System (SRS) “AIR
BAG” and “SEAT BELT PRE-TENSIONER”
The Supplemental Restraint System “Air Bag” and “Seat Belt Pre-tensioner”, used along with a seat belt,
helps to reduce the risk or severity of injury to the driver and front passenger in a frontal collision. The
Supplemental Restraint System consists of air bag modules (located in the center of the steering wheel and
on the instrument panel on the passenger side), seat belt pre-tensioners, a diagnosis sensor unit, warning
lamp, wiring harness and spiral cable. Information necessary to service the system safely is included in the
RS section
of the Service Manual.
If the vehicle is equipped with side air bag as the Supplemental Restraint System, the side air bag used along
with the seat belt helps to reduce the risk or severity of injury to the driver and front passenger in a side
collision. The side air bag consists of air bag modules (located in the outer side of front seats), satellite
sensor, diagnosis sensor unit (which is one of components of air bags for a frontal collision), wiring harness,
warning lamp (which is one of components of air bags for a frontal collision).
WARNING:
l
To avoid rendering the SRS inoperative (which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation) all maintenance must be per-
formed by an authorized NISSAN dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system.
l
Do not use electrical test equipment on any circuit related to the SRS unless instructed to do so
in this Service Manual. SRS wiring harnesses are covered with yellow insulation (either just
before the harness connectors or for the complete harness) for easy identification.
l
BT-2
 GENERAL SERVICING
Clip and Fastener
l
Clips and fasteners in BT section correspond to the following numbers and symbols.
l
Replace any clips and/or fasteners which are damaged during removal or installation.
Symbol
No.
Shapes
Removal & Installation
Removal:
Remove by bending up with
flat-bladed screwdrivers or
clip remover.
C101
SBF302H
SBF367BA
C103
Removal:
Remove with a clip remover.
SBT095
SBF423H
Push
Push center pin to
catching position.
(Do not remove
center pin by hitting it.)
C203
Push
Installation:
SBF258G
SBF708E
Removal:
Screwdriver
C205
Clip
Finisher
MBT080A
SBF638C
BT-3
 GENERAL SERVICING
Clip and Fastener (Cont’d)
Symbol
No.
Shapes
Removal & Installation
Removal:
Remove by bending up with a
flat-bladed screwdriver or pliers.
CE117
SBF174D
SBF175DA
Removal:
Clip-A
Flat-bladed screwdriver
Finisher
CF118
Clip-B
(Grommet)
Body
panel
Clip-B
(Grommet)
Sealing
washer
Clip-A
Sealing
washers
SBF151D
SBF259G
Removal:
Holder portion of clip must be spread
out to remove rod
CR103
SBF770B
SBF768B
Removal:
1. Screw out with a Phillips screwdriver.
2. Remove female portion with flat-bladed
screw-driver.
CS101
SBF078B
SBF992G
BT-4
BODY END
Body Front End
l
When removing or installing hood, place a cloth or other padding on the front fender panels and cowl
top. This prevents vehicle body from being scratched.
l
Bumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it.
l
Hood adjustment: Adjust at hinge portion.
l
Hood lock adjustment: After adjusting, check hood lock control operation. Apply a coat of grease to hood
locks engaging mechanism.
l
Hood opener: Do not attempt to bend cable forcibly. Doing so increases effort required to unlock hood.
2
Remove screws and clips
C205
securing left and right sides of front fender protector.
p
3
Remove screws securing radiator core support to bumper fascia.
p
4
Remove screws securing left and right front fenders to bumper fascia.
p
5
Remove clips
CS101
securing retainer to bumper fascia.
p
6
Extract bumper fascia assembly.
p
7
Remove screws securing fog lamps. Then remove fog lamps.
10.8 - 14.6 N·m
(1.1 - 1.5 kg-m,
8.0 - 10.8 ft-lb)
YBT001
BT-5
REMOVAL — Front bumper assembly
p
1
Remove clips
C205
securing bumper fascia to engine undercover.
p
  [ Pobierz całość w formacie PDF ]
  • zanotowane.pl
  • doc.pisz.pl
  • pdf.pisz.pl
  • klobuckfatima.xlx.pl